Distillation Part 1 (Laboratory Manual)

 

By : James W Zubrick
Email: j.zubrick@hvcc.edu

This separation or purification of liquids by vaporization and condensation is a very important step in one of man’s oldest professions. The word “still” lives on as a tribute to the importance of organic chemistry. The important points are

1. Vaporization. Turning a liquid to a vapor.

2. Condensation. Turning a vapor to a liquid.

Remember these. They show up on quizzes.

But when do I use distillation? That is a very good question. Use the guidelines below to pick your special situation, and turn to that section. But you should read all the sections, anyway.

1. Class 1: Simple distillation. Separating liquids boiling BELOW 150 °C at one atmosphere from

a. nonvolatile impurities.

b. another liquid boiling at least 25 ° C higher than the first. The liquids should dissolve in each another.

2. Class 2: Vacuum Distillation. Separating liquids boiling ABOVE 150 °C at 1 atm from

a. nonvolatile impurities.

b. another liquid boiling at least 25 °C higher than the first. They should dissolve in one another.

3. Class 3: Fractional Distillation. Separating liquid mixtures, soluble in each other, that boil at less than 25 °C from each other at 1 atm.


4. Class 4: Steam Distillation. Isolating tars, oils, and other liquid compounds insoluble, or slightly soluble, in water at all temperatures. Usually natural products are steam distilled. They do not have to be liquids at room temperatures {e.g., caffeine, a solid, can be isolated from green tea.).

Remember, these are guides. If your compound boils at 150.0001 °C don’t scream that you MUST do a vacuum distillation or both you and your product will die. I expect you to have some judgment and to pay attention to your instructor’s specific directions.

DISTILLATION NOTES

1. EXCEPT for Class 4, steam distillation, two liquids that are to be separated must dissolve in each other. If they did not, they would form separable layers, which you could separate in a separatory funnel (see Chapter 11, “Extraction and Washing”).

2. Impurities can be either soluble or insoluble. For example, the material that gives cheap wine its unique bouquet is soluble in the alcohol. If you distill cheap wine, you get clear grain alcohol separated from the “impurities,” which are left behind in the distilling flask.

CLASS 1: SIMPLE DISTILLATION

For separation of liquids boiling below 150 °C at 1 atm from

1. nonvolatile impurities.

2. another liquid boiling 25 °C higher than the first liquid. They must dissolve in each other.

Sources of Heat

If one of the components boils below 70 °C and you use a Bunsen burner, you may have a hard time putting out the fire. Use a steam bath or a heating mantle. Different distillations will require different handling (see Chapter 13, “Sources of Heat”). All the distillations always require heating, so the sources of heat chapter is really closely tied to this section. This goes for enlightenment on the use of boiling stones and clamps as well (see Chapter 12, “And Now—Boiling Stones” and Chapter 14, “Clamps and Clamping”).

The 3-Way Adapter

If there is any one place your setup will fall apart, here it is (Fig. 73). When you set up the jointware, it is important that you have all the joints line up. This is tricky, since, as you push one joint together, another pops right out. If you’re not sure, call your instructor. Let him inspect your work. Remember,

All joints must be tight!

 A complete, entire simple distillation setup.

Fig. 72 A complete, entire simple distillation setup.

The Distilling Flask

Fill the distilling flask with the liquid you want to distill. You can remove the thermometer and thermometer adapter, fill the flask using a funnel, then put the thermometer and its adapter back in place.

If you’re doing a fractional distillation with a column (a class 3 distillation), you should’ve filled the flask before clamping the setup. (Don’t ever pour your mixture down a column. That’ll contaminate everything!) You’ll just have to disassemble some of the setup, fill the flask, reassemble what you’ve taken down, and pray that you haven’t knocked all the other joints out of line.

Don’t fill the distilling flask more than half full. Put in a boiling stone if you haven’t already. These porous little rocks promote bubbling and keep the liquid from superheating and flying out of the flask. This flying around is called bumping. NEVER drop a boiling stone into hot liquid or you may be rewarded by having your body soaked in the hot liquid as it foams out at you.

Make sure all the joints in your setup are tight. Start the heat S-L-O-W-L-Y until gentle boiling begins and liquid starts to drop into the receiving flask at the rate of about 10 drops per minute. This is important. If nothing comes over, you’re not distilling, merely wasting time. You may have to turn up the heat to keep material coming over.

The commonly camouflaged until it's too late open joint.

Fig. 73 The commonly camouflaged until it’s too late open joint.

The Thermometer Adapter

Read all about it. Ways of having fun with thermometer adapters have been detailed (see text accompanying Fig. 22).

The Ubiquitous Clamp

A word about clamps. Use! They can save you $68.25 in busted glassware (see Chapter 14, “Clamps and Clamping”).

The Thermometer

Make sure the ENTIRE thermometer bulb is below the sidearm of the 3-way adapter. If you don’t have liquid droplets condensing on the thermometer bulb, the temperature you read is nonsense. Keep a record of the temperature of the liquid or liquids that are distilling. It’s a check on the purity. Liquid collected over a 2 ° C range is fairly pure. Note the similarity of this range with that of the melting point of a pure compound (see Chapter 9, “The Melting Point Experiment”).

The Condenser

Always keep cold water running through the condenser, enough so that at least the lower half is cold to the touch. Remember that water should go in the bottom and out of the top (Fig. 72). Also, the water pressure in the lab may change from time to time and usually goes up at night, since little water is used then. So, if you are going to let condenser cooling water run overnight, tie the tubing on at the condenser and the water faucet with wire or something. And if you don’t want to flood out the lab, see that the outlet hose can’t flop out of the sink.

The Vacuum Adapter

It is important that the tubing connector remain open to the air or else the entire apparatus will, quite simply, explode.

WARNING: Do not just stick the vacuum adapter on the end of the condenser and hope that it will not fall off and break.

This is foolish. I have no sympathy for anyone who will not use clamps to save their own breakage fee. They deserve it.

The Receiving Flask

The receiving flask should be large enough to collect what you want. You may need several, and they may have to be changed during the distillation. Standard practice is to have ONE flask ready for what you are going to throw away and others ready to save the stuff that you want to save.

The Ice Bath

Why everyone insists on loading up a bucket with ice and trying to force a flask into this mess, I’ll never know. How much cooling do you think you’re going to get with just a few small areas of the flask barely touching ice? Get a suitable receptacle—a large beaker, enamelled pan, or whatever. It should, not leak. Put it under the flask. Put some water in it. Now add ice. Stir. Serves four.

THE DISTILLATION EXAMPLE

Say you place 50 ml of liquid A (B.P. 50 °C) and 50 ml of liquid B (B.P. 100° C) in 250 ml R.B. flask. You drop in a boiling stone, fit the flask in a distillation setup, and turn on the heat. Bubbling starts and soon droplets form on the thermometer bulb. The temperature shoots up from room temperature to about 35°C, and a liquid condenses and drips into the receiver. That’s bad. The temperature should be close to 50 °C. This low-boiling material is the forerun of a distillation, and you won’t want to keep it.

Keep letting liquid come over until the temperature stabilizes at about 49 °C. Quick! Change receiving flasks NOW!

The new receiving flask is on the condenser and the temperature is about 49° C. GOOD. Liquid comes over and you heat to get a rate of about 10 drops per minute collected in the receiver. As you distill, the temperature slowly increases to maybe 51°C then starts moving up rapidly.

Here you stop the distillation and change the receiver. Now in one receiver you have a pure liquid, B.P. 49-51°C. Note this boiling range. It is just as good a test of purity as a melting point is for solids (see Chapter 11, “The Melting Point Experiment”).

Always report a boiling point for liquids as routinely as you report melting points for solids. The boiling point is actually a boiling range, and should be reported as such:

“B.P. 49-51 °C”

If you now put on a new receiver, and start heating again, you may discover more material coming over at 50°C! Find that strange? Not so. All it means is that you were distilling too rapidly and some of the low-boiling material was left behind. It is very difficult to avoid this situation. Sometimes it is best to ignore it, unless a yield is very important. You can combine this “new” 50°C fraction with the other good fraction.

For B, boiling at 100°C, merely substitute some different boiling points and go over the same story.

THE DISTILLATION MISTAKE

OK, you set all this stuff up to do a distillation. Everything’s going fine. Clamps in the right place. No arthritic joints, even the vacuum adapter is clamped on, and the thermometer is at the right height. There’s a bright golden haze on the meadow and everything’s going your way. So, you begin to boil the liquid. You even remembered the boiling stone. Boiling starts slowly, then more rapidly. You think, “This is it?’ Read that temperature, now. Into the notebook: “The mixture started boiling at 26 °C”

And you are dead wrong.

What happened? Just ask—

Is there liquid condensing on the thermometer bulb??

NOI

So, congratulations, you’ve just recorded the room temperature. There are days when over half the class will report distillation temperatures as “Hey I see it start boiling now” temperatures. Don’t participate. Just keep watching as the liquid boils. Soon, droplets will condense on the thermometer bulb. The temperature will go up quickly, then stabilize. NOW read the temperature. That’s the boiling point.

CLASS 2: VACUUM DISTILLATION

For separation of liquids boiling above 150 °C at 1 atm from

1. nonvolatile impurities.

2. another liquid boiling 25 °C higher than the first liquid. They must dissolve in each other. This is like the simple distillation with the changes shown (Fig. 74).

Why vacuum distill? If the substances boil at high temperatures at 1 atm, they may decompose when heated. Putting a vacuum over the liquid makes the liquid boil at a lower temperature. With the pressure reduced, there are fewer molecules in the way of the liquid you are distilling. Since the molecules require less energy to leave the surface of the liquid, you can distill at a lower temperature, and your compound doesn’t decompose.

Pressure Measurement

If you want to measure the pressure in your vacuum distillation setup, you’ll need a closed-end manometer. There are a few different types, but they all work essentially the same way. I’ve chosen a “stick” type (Fig. 75). This particular model needs help from a short length of rubber tubing and a glass T to get connected to the vacuum distillation setup.

A vacuum distillation set up.

Fig. 74 A vacuum distillation set up.

1. Turn on the source of vacuum and wait a bit for the system to stabilize.

2. Turn the knob on the manometer so that the notch in the joint lines up with the inlet.

3. Wait for the mercury in the manometer to stop falling.

4. Read the difference between the inner and outer levels of mercury. This is the system pressure, literally in millimeters of mercury, that we now call torr.

5. Turn the knob on the manometer to disconnect it from the inlet. Don’t leave the manometer permanently connected. Vapors from your distillation, water vapor from the aspirator, and so on, may contaminate the mercury.

Manometer Hints

1. Mercury is toxic, the vapor from mercury is toxic, mercury spilled breaks into tiny globules that evaporate easily and are toxic, it’ll alloy with your jewelry, and so on. Be very careful not to expose yourself (or anyone else) to mercury.

 A closed-end "stick" manometer.

Fig. 75 A closed-end “stick” manometer.

2. If the mercury level in the inner tubes goes lower than that of the outer tube it does NOT mean that you have a negative vacuum. Some air or other vapor has gotten into the inner stick, and with the vacuum applied, the vapor expands and drives the mercury in the inner tube lower than that in the outer tube. This manometer is unreliable and you should seek a replacement.

3. If a rubber tube connected to the vacuum source and the system (or manometer) collapses, you’ve had it. The system is no longer connected to the vacuum source, and as air from the bleed tube or vapor from the liquid you’re distilling fills your distillation setup, the pressure in the system goes up. Occasionally test the vacuum hoses and if they collapse under vacuum, replace them with sturdier hoses that can take it.

Leaks

Suppose, by luck of the draw, you’ve had to prepare and purify 1-octanol (B.P. 195°C). You know if you simply distill 1-octanol, you run the risk of having it decompose, so you set up a vacuum distillation. You hook your setup to a water aspirator and water trap and attach a closed-end “stick” manometer. You turn the water for the aspirator on full-blast and open the stick manometer. After a few minutes, nothing seems to be happening. You pinch the tubing going to the vacuum distillation setup, (but not to the manometer) closing the setup off from the source of vacuum. Suddenly, the mercury in the manometer starts to drop. You release the tube going to the vacuum distillation setup, and the mercury jumps to the upper limit. You have air leaks in your vacuum distillation setup.

Air leaks can be difficult to find. At best, you push some of the joints together again and the system seals itself. At worst, you have to take apart all the joints and regrease every one. Sometimes you’ve forgotten to grease all the joints. Often “a joint has been etched to the point that it cannot seal under vacuum, when it is perfectly fine for other applications. Please get help from your instructor.

Next post:

Previous post: