Adding TLS 1.2 Support to Your TLS Library - Implementing SSL/TLS Using Cryptography and PKI - page 526

0xFF, 0xFF, 0xFF, 0xFF, 0x99, 0xDE, 0xF8, 0x36,
0x14, 0x6B, 0xC9, 0xB1, 0xB4, 0xD2, 0x28, 0x31
};
unsigned char prime256v1_P[] = {
0xFF, 0xFF, 0xFF, 0xFF, 0x00, 0x00, 0x00, 0x01,
0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
0x00, 0x00, 0x00, 0x00, 0xFF, 0xFF, 0xFF, 0xFF,
0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF
};
unsigned char prime256v1_A[] = {
0xFF, 0xFF, 0xFF, 0xFF, 0x00, 0x00, 0x00, 0x01,
0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
0x00, 0x00, 0x00, 0x00, 0xFF, 0xFF, 0xFF, 0xFF,
0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFC
};
unsigned char prime256v1_B[] = {
0x5A, 0xC6, 0x35, 0xD8, 0xAA, 0x3A, 0x93, 0xE7,
0xB3, 0xEB, 0xBD, 0x55, 0x76, 0x98, 0x86, 0xBC,
0x65, 0x1D, 0x06, 0xB0, 0xCC, 0x53, 0xB0, 0xF6,
0x3B, 0xCE, 0x3C, 0x3E, 0x27, 0xD2, 0x60, 0x4B
};
unsigned char prime256v1_Gx[] = {
0x6B, 0x17, 0xD1, 0xF2, 0xE1, 0x2C, 0x42, 0x47,
0xF8, 0xBC, 0xE6, 0xE5, 0x63, 0xA4, 0x40, 0xF2,
0x77, 0x03, 0x7D, 0x81, 0x2D, 0xEB, 0x33, 0xA0,
0xF4, 0xA1, 0x39, 0x45, 0xD8, 0x98, 0xC2, 0x96
};
unsigned char prime256v1_Gy[] = {
0x4F, 0xE3, 0x42, 0xE2, 0xFE, 0x1A, 0x7F, 0x9B,
0x8E, 0xE7, 0xEB, 0x4A, 0x7C, 0x0F, 0x9E, 0x16,
0x2B, 0xCE, 0x33, 0x57, 0x6B, 0x31, 0x5E, 0xCE,
0xCB, 0xB6, 0x40, 0x68, 0x37, 0xBF, 0x51, 0xF5
};
unsigned char prime256v1_N[] = {
0xFF, 0xFF, 0xFF, 0xFF, 0x00, 0x00, 0x00, 0x00,
0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
0xBC, 0xE6, 0xFA, 0xAD, 0xA7, 0x17, 0x9E, 0x84,
0xF3, 0xB9, 0xCA, 0xC2, 0xFC, 0x63, 0x25, 0x51
};
int get_named_curve( const char *curve_name, elliptic_curve *target )
{
if ( !strcmp( “prime192v1”, curve_name ) ||
!strcmp( “secp192r1”, curve_name ) )
{
load_huge( &target->p, prime192v1_P, sizeof( prime192v1_P ) );
load_huge( &target->a, prime192v1_A, sizeof( prime192v1_A ) );
load_huge( &target->b, prime192v1_B, sizeof( prime192v1_B ) );