Biomedical Engineering Reference
In-Depth Information
37. Chen, M., Liu, D., You, C., Yang, X., and Cui, Z. 2007. Interfacial characteristic of graded hydroxy-
apatite and titanium thin film by magnetron sputtering. Surf Coat Technol 201: 5688-5691.
38. Ueda, K., Kawasaki, Y., Narushima, T., et al. 2009. Calcium phosphate films with/without heat
treatments fabricated using RF magnetron sputtering. J Biomech Sci Eng 4: 392-403.
39. Aoki, H. 1989. Surface design and functions of hydroxyapatite. J Surf Sci Soc Jpn 10: 96-101.
40. Nakano, T., Fujitani, W., and Umakoshi, Y. 2004. Synthesis of apatite ceramics with preferential
crystal orientation. Mater Sci Forum 449-452: 1289-1292.
41. Hoepfner, T.P. and Case, E.D. 2004. An estimate of the critical grain size for microcracks induced
in hydroxyapatite by thermal expansion anisotropy. Mater Lett 58: 489-492.
42. Nakano, T., Kaibara, K., Tabata, Y., et al. 2002. Unique alignment and texture of biological apa-
tite crystallites in typical calcified tissues analyzed by microbeam X-ray diffractometer system.
Bone 31: 479-487.
43. van Dijk, K., Schaeken, H.G., and Wolke, J.C.G., et al. 1995. Influence of discharge power level
on the properties of hydroxyapatite films deposited on Ti6Al4V with RF magnetron sputtering.
J Biomed Mater Res 29: 269-276.
44. Nelea, V., Morosanu, C., Iliescu, M., and Mihailescu, I.N. 2003. Microstructure and mechanical
properties of hydroxyapatite thin films grown by RF magnetron sputtering. Surf Coat Technol
173: 315-322.
45. Haman, J.D., Scripa, R.N., Rigsbee, J.M., and Lucas, L.C. 2002. Production of thin calcium phos-
phate coatings from glass source materials. J Mater Sci Mater Med 13: 175-184.
46. Ding, S.-J., Ju, C.-P., and Chern Lin, J.-H. 1999. Characterization of hydroxyapatite and titanium
coatings sputtered on Ti-6Al-4V substrate. J Biomed Mater Res 44: 266-274.
47. Yoshinari, M., Oda, Y., Inoue, T., and Shimono, M. 2002. Dry-process surface modification for
titanium dental implants. Metall Mater Trans A 33A: 511-519.
48. Zeng, H., Lacefield, W.R., and Mirov, S. 2000. Structural and morphological study of pulsed
laser deposited calcium phosphate bioceramic coatings: Influence of deposition conditions,
laser parameters, and target properties. J Biomed Mater Res , 50: 248-258.
49. Bryant, W.A. 1977. Review: The fundamentals of chemical vapor deposition. J Mater Sci 12:
1285-1306.
50. Clarke, D.R. and Levi, C.G., 2003. Materials design for the next generation thermal barrier coat-
ings. Annu Rev Mater Res 33: 383-417.
51. Kadokura, H., Itoh, A., Kimura, T., and Goto, T. 2010. Moderate temperature and high-speed
synthesis of α-Al 2 O 3 films by laser chemical vapor deposition using Nd:YAG laser. Surf Coat
Technol 204: 2302-2306.
52. Tu, R. and Goto, T. 2005. Thermal cycle resistance of yttria stabilized zirconia films prepared by
MOCVD. Mater Trans 46: 1318-1323.
53. Pattanaik, A.K. and Sarin, V.K. 2001. Basic principles of CVD thermodynamics and kinetics. In
Park, J.-H. (ed.), Chemical Vapor Deposition , Surface Engineering Series Vol. 2, pp. 23-43. Materials
Park, OH: ASM International.
54. Duty, C., Jean, D., and Lackey, W.J. 2001. Laser chemical vapor deposition: Materials, modeling,
and process control. Inter Mater Rev 46: 271-287.
55. Kimura, T. and Goto, T. 2003. Rapid synthesis of yttria-stabilized zirconia films by laser chemi-
cal vapor deposition. Mater Trans 44: 421-424.
56. Endo, J., Itoh, A., Kimura, T., and Goto, T. 2010. High-speed deposition of dense, dendritic
and porous SiO 2 films by Nd: YAG laser chemical vapor deposition. Mater Sci Eng B 166:
225-229.
57. Sato, M., Tu, R., Goto, T., Ueda, K., and Narushima, T. 2008. Preparation of Ca-Ti-O/Ca-P-O
functionally graded bio-ceramic film by MOCVD. J Jpn Soc Powder Powder Metallurgy 55:
325-330.
58. Allen, G.C., Ciliberto, E., Fragalà, I., and Spoto, G. 1996. Surface and bulk study of calcium
phosphate bioceramics obtained by metal organic chemical vapor deposition. Nucl Instrum
Meth B 116: 457-460.
Search WWH ::




Custom Search